// CÔNG TY CỔ PHẦN THƯƠNG MẠI DỊCH VỤ VÀ KỸ THUẬT WIN - vinh dự là nhà phân phối các sản phẩm cơ điện tử - điện lạnh uy tín tại Việt Nam //

Hỗ trợ khách hàng :

0933.707.707 Hỗ trợ trực tuyến :

Mạng Xã Hội:

Tỉ Giá Ngoại Tệ :

Thống Kê Truy Cập :

Users on page

Now online: 1
Hôm Nay: 32
Tuần Này: 32
Tổng Lượt Xem: 36849

( Rê chuột để phóng lớn )

Cảm biến áp suất DPIL

Model : DPIL

Xuất Xứ : Liên hệ

Tình Trạng : Liên hệ

Giá Bán : Liên hệ

Bảo Hành : 12 tháng

Để có được giá tốt nhất, quý khách vui lòng liên hệ 0933.707.707 gặp Mr Lãm


DPIL Liquid Differential Pressure Sensor

Cảm biến chênh áp

The DPIL is suitable for measurement of differential pressures
across pumps, boilers, chillers, filters etc. in HVAC applications.
The use of thick film resistances fixed on a ceramic chip gives
no mechanical ageing or creepage. The sensor is loop-powered
giving a 4 to 20 mA signal equivalent to the measuring range.
Electrical connection is via a DIN (4350-A) IP65 connector
supplied) and pressure connections are screw compression
fittings for 6 mm pipe. It is supplied complete with a mounting
• Wide temperature range
• 4 to 20 mA output
• IP65 Housing

The differential pressure is applied across a ceramic chip onto which are fixed thick film resistances. The ceramic chip is protected
from the medium by EPDM (Ethylene propylene) seals. The internal amplifier produces a 2 wire (loop-powered) 4 to 20 mA signal.
The pressure connections are screw compression fittings for 6 mm outside diameter pipes.
The electrical connection is via a DIN 43650-A connector with IP65 seal suitable for 11 mm (0.43”) outside diameter cable.

Output :4 to 20 mA (protected against polarity
Accuracy :± 1.3% full scale (/0.5, /1, /2.5)
± 0.8% full scale (/4)
± 0.5% full scale (/6, /10)
coefficient :± 0.1% full scale /°C, 0.055%/°F (/0.5, /1, /2.5)
± 0.06% full scale /°C, 0.033%/°F (/4)
± 0.04% full scale /°C, 0.022%/°F (/6, /10)
Power :11 to 33 Vdc
Supply Current :25 mA (max)
System pressure :Maximum overpressure (P1 and P2
simultaneously) 25 bar
Overload pressure :Maximum overpressure (P1 or P2
separately) see table in order code section.
Ruptive pressure :37.5 bar
Dimensions :77 mm x 125 mm x 40 mm (max) (3.03”
x 4.92” x 1.57”)
77 mm x 145 mm x 40 mm (3.03” x 5.71”
x 1.57”) including bracket
Weight :494g (1.09 lbs)
Load cycle :50 Hz (max)
Dynamic response :Response time <5 ms
Pressure connectors:Screw compression fittings (CuZn vni)
for 6 mm O/D pipe
Connections :DIN 43650-A (IP65)
Materials :housing in contact with medium:
Ceramic/INOX 1.4305, PTFE
:seals: EPDM (Ethylene propylene)
Temperature :medium and ambient : -15 °C to +80 °C
(+5 °F to +176 °F)
Protection :IP65
Immunity :EN50082-1, and -2
Input channel and sensor scaling
The input channel should be linked for loop powered current, I.
The sensor type module must be set up with the correct scaling.
The recommended method of setting the sensor type scaling is
to use SET. For all IQ2 series controllers with firmware version
2.1 or greater, or IQ3 series controllers, the appropriate SET
Unique Sensor Reference given below should be used.
Pressure I 0.5 bar
Pressure I 1 bar
Pressure I 2.5 bar
Pressure I 4 bar
Pressure I 6 bar
Pressure I 10 bar
Alternatively set scaling mode to 5 (characterise) and enter
scaling manually as defined in appropriate table below. Note that
for IQ3 the scaling mode and exponent (E) do not need to be
set up.

Các sản phẩm khác cùng loại :

Water meter EW370
Model : EW370

Water meter EW120
Model : EW120

Water meter EW171
Model : EW171

Water meter EW130
Model : EW130

Công Ty Cổ Phần Thương Mại Dịch Vụ Và Kỹ Thuật WIN
Địa chỉ : 1047 Lũy Bán Bích, Phường Tân Thành, Quận Tân Phú, Thành Phố Hồ Chí Minh.
Tel : (+84) 838.490.793 - Fax : (+84) 838.490.795 - Email : sales@wincorp.com.vn - Website : www.wincorp.com.vn